NEW ARRIVALS! Hantek DSO4202C Digital Oscilloscope 2CH,200MHz Bandwidth,1GSa/s

Item No.:Hantek DSO4202C
The item located in Sydney, Australia We ship to you only 5-7 days, 3 years warranty. No Shipping Cost, No VAT. The price is all included.
Buy it Now: AUD489.00   FREE Shipping
Quantity :
         Sub Total: AUD489.00
Manufacturer Specifications:

DSO4000C Series
2 Channel Digital Oscilloscope. 1 Channel Arbitrary/Function Waveform Generator. The Keys for osilloscope and waveform generator is seperated for convenient to operate it simultaneously. Oscilloscope: 200/100/70MHz Bandwidth, 1GSa/s Sample Rate. 25MHz Arbitrary waveform generator, 12 bits resolution, 200MHz DDS, 7 inch 64K color LCD display, Resolution 800x480.

DSO 4072C Feature:

  • 70MHz Bandwidth; 1GSa/s Sample Rate;
  • 2 Channel Oscilloscope; 40K Record Length;
  • 7 inch 64K color LCD display, Resolution 800x480;
  • 32 kinds of Automotive measurement, with FFT function;
  • 25MHz Arbitrary waveform output (Sine wave up to 75MHz);
  • Powerful trigger function: Video, Edge, Pluse Width, Slope, Overtime, Alternate Trigger.






Sample Rate

Sampling Rate Range: 1GSa/s


Equivalent Sample Rate: 25GSa/s

Acquisition Modes


Normal data only

Peak Detect

High-frequency and randon glith capture


Wavefom Average, selectable 4,8,16,32,64,128


Inputs Coupling


Inpits Impendance

1MΩ±2% ‖20pF±3pF

Probe Attenuation

1X, 10X

Supported Probe Attenuation Factor

1X, 10X, 100X, 1000X

Maximum Input Voltage

CAT I and CAT II: 300VRMS (10×)


CAT III: 150VRMS(1×);

Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur.


Sample Rate Range


Waveform Interpolation

(sin x)/x

Record Length



2ns/div to 40s/div

4ns/div to 40s/div

Sample Rate and

±50ppm(at over any ≥1ms time interval)

Delay Time Accuracy

Position Range

2ns/div to 10ns/div;

20ns/div to 80us/div; (-8div x s/div) to 40ms;


(-4div x s/div) to 20ms;

200us/div to 40s/div; (-8div x s/div) to 400s

Delta Time Measurement Accuracy
(Full Bandwidth)

Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns);
>16 averages:± (1 sample interval + 100ppm × reading + 0.4ns);
Sample interval = s/div ÷ 200


Vertical Resolution

8-bit resolution, all channel sampled simultaneously

Position Range

2mV/div to 10V/div





Rise Time at BNC( typical)




Analog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled

2mV/div to 20mV/div, ±400mV; 50mV/div to 200mV/div, ±1V


500mV/div to 2V/div, ±40V; 5V/div, ±50V


+, -, *, /, FFT


Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman;


1024 sample point

Bandwidth Limit


Low Frequency Response (-3db)

≤10Hz at BNC

DC Gain Accuracy

±3% for Normal or Average acquisition mode, 5V/div to 10mV/div;


±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div

DC Measurement Accuracy, 
Average Acquisition Mode

When vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected; 
When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div

Volts Measurement Repeatability, Average Acquisition Mode

Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions

Trigger System

Trigger Types

Edge, Video, Pulse, Slope, Over time, Alternative

Trigger Source

CH1, CH2, EXT, EXT/5, AC Line

Trigger Modes

Auto, Normal, Single

Coupling Type

DC, AC, Noise Reject, HF Reject, LF Reject

Trigger Sensitivity
(Edge Trigger Type)



1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;


200mV from DC to 100MHz; 350mV from 100MHz to 200MHz;


1V from DC to 100MHz;1.75V from 100MHz to 200MHz;

AC: Attenuates signals below 10Hz;

HF Reject: Attenuates signals above 80kHz;

LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz

Trigger Level Range

CH1/CH2: ±8 divisions from center of screen;


EXT: ±1.2V;


Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20ns

CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen;


EXT: ± (6% of setting + 40mV);

EXT/5: ± (6% of setting + 200mV);

Set Level to 50%(typical)

Operates with input signals ≥50Hz

Video Trigger

Video Trigger Type

CH1, CH2: Peak-to-peak amplitude of 2 divisions;


EXT: 400mV;

EXT/5: 2V

Signal Formats and Field Rates, Video Trigger Type

Supports NTSC, PAL and SECAM broadcast systems for any field or any line

Holdoff Range

100ns ~ 10s

Pulse Width Trigger

Pulse Width Trigger Mode

Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse

Pulse Width Trigger Point

Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.
Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.
Less than: The trigger point is the trailing edge.
Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width

Pulse Width Range

20ns ~ 10s

Slope Trigger

Slope Trigger Mode

Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope

Slope Trigger Point

Equal: The oscilloscope triggers when the waveform slope is equal to the set slope.


Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.

Less than: The oscilloscope triggers when the waveform slope is less than the set slope.

Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.

Time Range

20ns ~ 10s

Overtime Trigger

Over Time Mode

Rising edge or Falling edge

Time Range

20ns ~ 10s

Alternative Trigger

Trigger on CH1

Internal Trigger: Edge, Pulse Width, Video, Slope

Trigger on CH2

Internal Trigger: Edge, Pulse Width, Video, Slope

Trigger Frequency Counter

Readout Resolution

6 digits

Accuracy (typical)

±30ppm (including all frequency reference errors and ±1 count errors)

Frequency Range

AC coupled, from 4Hz minimum to rated bandwidth

Signal Source

Pulse Width or Edge Trigger modes: all available trigger sources


The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed.

Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time.

Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity.

Video Trigger mode: The Frequency Counter does not work.


Cursor Measurement

Voltage difference between cursors: △V


Time difference between cursors: △T

Reciprocal of △T in Hertz (1/ΔT)

Auto Measuerment

Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time,


+Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid,

Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH,


Signal Source Mode

Waveform Impedance


Sample Rate


Output Waveform

Arbitrary wave/square wave/sine wave/triangle wave/trapezoidal wave/pulse wave/DC

Frequency Resolution


Waveform Depth


Vertical Resolution


Frequency Stability


Waveform Range

±3.5V Max

Output Impedance


Output Current

50mA Ipeak=100mA

System BW


Harmonic Distortion


General Features


Display Type

7 inch 64K color TFT (diagonal liquid crystal)

Display Resolution

800 horizontal by 480 vertical pixels

Display Contrast

Adjustable (16 gears) with the progress bar

Probe Compensator Output

Output Voltage( typical)

About 5Vpp into ≥1MΩ load



Power Supply

Supply Voltage

100-120VACRMS(±10%), 45Hz to 440Hz, CATⅡ


120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ

Power Consumption



2A, T rating, 250V



Operating: 32℉ to 122℉ (0℃ to 50℃);


Nonoperating: -40℉ to 159.8℉ (-40℃ to +71℃)

Cooling Method



+104℉ or below (+40℃ or below): ≤90% relative humidity;


106℉ to 122℉ (+41℃ to 50℃): ≤60% relative humidity


Operating: Below 3,000m (10,000 feet);


Nonoperaring: Below 15,000m(50,000 feet)



Length 385mm, Width 200mm, Height 245mm


3.5KG(with Packing); 2.08KG(without Packing)


Function Pictures:



Package content:








Write a Review

Tell us what you think about this item and share your opinions with other people. Please make sure your review focuses only on this item. All reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.

After-sales questions and issues: Contact our Customer Service Department. (A customer representative will get back to you).

Please Sign In first if you want to later edit or manage reviews uploaded by yourself.

* Rating:
    Please select rating stars.
* Your First & Last Name:
* Your E-Mail Address:
* Review Title:
* Review Detail:
Stay Tuned!
Get updates on sales and discount offers.